How do I install a trailer brake controller on dodge journey How do I install a trailer brake controller and a 7 pin - Dodge 2009 Journey question. 2008 dodge 1500 4wd tail light wire harness. Still need to raise trailer 7'. 2001 Dodge Ram 2500 4x4 stock height, 2004 Durango axles under springs now, any suggestions? Installation of a Trailer Brake Controller on a 2006 Dodge Ram 1500 - etrailer.com. Today on our 2006. Subscribe: Prodigy P2 - Trailer Brake Controller by Tekonsha (Brake Controller) BRAKE CNTRL 7 WAY DELUXE INST KIT, 10 ga by etrailer (Accessories and Parts) is the world's leading online retailer of custom-fit towing accessories. We carry thousands of vehicle accessories such as custom-fit trailer hitches for over 3,100 different vehicles, performance chips, heavy-duty towing supplies, trailer parts, bike racks, cargo carriers, step bars, tonneau covers, lights, car covers, RV supplies, floor mats, and much more, to help you make your vehicle more useful and more fun. Our decades of experience and enormous buying power ensure that you will get quality parts, and excellent service, at the lowest price possible. All this is backed by our Satisfaction Guarantee() and our Lowest Price Pledge(). Full transcript: Today on our 2007 Dodge Durango, we'll be installing the Tekonsh Prodigy P2 brake controller, part number 90885. In order to install this brake controller on this vehicle, we'll also need to use the e-trailer universal install kit, part number ETBC7. To start, we'll first food ahead and assemble the 7 pull adapter bracket. With hardware provided, we'll use it to attach the bracket to the 7 pull adapter. We'll go ahead and take the bracket, feed it over the wires and up to the back of the mounting surface for the 7 pull adapter. Then, we'll take the screws, feed them through the front side of the 7 pull and secure it with the nuts in the back side. Once we have all 4 in place, we'll go ahead and tighten them down. I'm going to go ahead and take some black electrical tape and wrap up 8 to 10 inches of our wire. This will assist in bundling our wires together and help protect it from the elements. Note; we've cut short the purple wire for the reverse light for trailer as it will not be necessary for this application. Next, we'll go ahead and attach the drop tight, no drill mounting bracket, part number 18136. Using the fasteners provided with the bracket, we can secure it to the 7 pull bracket. The vehicle is already equipped with a 4 pull flat connector. How To Install A Brake Controller 2008 Dodge RamThe connector is a bit corroded and has excess wire, so we're going to go ahead and cut off the excess wire on the vehicle side and the 4 flat connector on the back of our 7 pull. Now, we're ready to install our 7 pull connector on to the vehicle. Manual de reparacion de toyota tercel 1995 dx for sale. We'll use the worm gear clamp provided to secure it directly to the hitch tube. We'll strip back both sides of the wire, using the Deka heat shrink butt connectors and connect color for color, brown to brown, yellow to yellow and green to green. Using our Deka heat shrink butt connectors, part number Dw05744. Once we crimp the connection points, we'll then use the heat gun to heat up the shrinkable tubing on the outside of the butt connector to seal it up. Next we'll go ahead and prepare our grey duplex cable to connect it to the 7 pull wiring. To do this, we'll need to strip back some of the gray sheathing. We'll use our utility knife to slice the sheathing and then cut it off. We'll strip back both the white and black wires. Now, we can take the white wire, connect it with the blue wire, coming out of the back of the 7 pull connector. There's already a butt connector on the blue side, so we'll just simply connect it and crimp it down. On a normal or standard install, the black power wire coming from the converter box for the 4 pull wiring harness install, would have a additional black wire that would lead up to the front of the vehicle and ultimately to the battery, but because we're installing our ETBC7 brake controller install kit, and the black power wire that'll be run to power the inaudible constant supply for our 7 pull connector, here at the back of the vehicle, it's thick enough to carry the load for both harnesses. How To Install A Brake Controller 2008 Dodge Ram PartsWe'll go ahead and connect the harnesses together and run 1 power wire to the front of the vehicle. Twist the wires together. Once we've got them firmly twisted together, we use a weather-proof wire nut. This can be purchased from your local hardware or auto parts stores. Now, with our power wires secured, to help keep them together, we're going to go ahead and secure them with a small zip tie. Next, we'll take our white wire which is our ground wire for our module box and attach it to the body of the vehicle using a self-tapping screw, provided with our install kit. Now, we're ready to tape up all of our connection points to help bundle them together, keep them free from dirt, dust, debris, moisture and clean up. Features: Mount the control knob of this proportional controller on your dash or console, and affix the main unit in an out-of-the-way spot. 3-Axis accelerometer ensures unit works no matter its positioning. How To Install A Brake Controller 2008 Dodge Ram 1500Switch modes to get preset braking for off-roading. Installation Notes: You need item ($69.64) to install your controller. Brake (blue) wire does not run all the way back to the 4-pole at the rear; it stops at the connector that is located under the driver's side wheel well. In order to finalize the installation you must splice into this wire and continue it back to the plug.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |